Tulosta Sähköposti

Technical information

BRO Starke Basic

Lifting capacity
20 ton
Lifting height, approx.
5 m
Weight, recovery unit
8 ton

CHASSIS

Suitable chassis, three or four axle forward control. Wheelbase with 3 or 4 axle will be from 5,10 to 5,30 m. Frontaxle 9 ton for a 3 axle and 2 x 8 ton for 4 axles. For a four axle chassis the front axle minimum capacity is 2 x 7 tons. Vertical exhaust system and equipped with power take off (PTO) for direct mounted pump. High speed approx. 1:1.2.


RECOVERY UNIT

BB 9010
The recovery unit is hydraulically operated. The material we have chosen is Swedish extra high-tensile steel (Re 640-700 mm²). Main components:
  • sub frame
  • two stiff legs
  • lifting boom with two double acting telescopic cylinders (two stage)
  • folding and extendible boom (2 x 750 mm)
  • folding and extendible boom (2 x 1100 mm)
BB 9041
The components in the recovery unit are sandblasted, primed black (RAL 9005) and top coated for maximum resistance against corrosion. The exposed parts of the extendible boom are chromated. Lubrication points are piped out for easy access.
BB 9015
After top coating the components of the recovery unit they are refitted on the chassis.
BB 9009
Once the recovery unit is completed and final coating done the final assembly is made.

SUB FRAME

The sub frame is made of rectangular sections of extra high tensile steel. The recovery unit is fitted on the chassis according to the directions of the truck manufacturer.


STIFF LEGS

The stiff legs are made of extra high-tensile steel with wide toothed spades for maximum holding capacity and with integrated foldable ground plates. The stiff legs are separately hydraulically operated.


LIFTING BOOM

The lifting boom is supported by strong bronze bearings which gives a long service life. The wire outlet of the main winch goes through the lifting boom, which at the rear outlet has a large turnable sheave for the wire. On the second winch the wire runs on top of the lifting booms and over the turnable guidance. The lifting boom action is controlled by two double acting telescopic cylinders (two stage).


FOLDING AND EXTENDIBLE BOOM

BB 9017
The folding boom bearings are situated at the rearmost of the lifting boom. The folding boom is run up to transport position by the hydraulic power tilt cylinder. The extendible boom, lockable in eight positions, with three parallel running cylinders (2x750 mm) runs the folding boom. At the rearmost of the extendible boom is the lifting bar carried in bearings.
BB 4357
For a 4 axle truck the extendible boom 2 x 1100mm is required and has 10 different locking positions.

COMPARTMENTS

BB 9034
The compartments are manufactured of 3 mm cold-rolled sheet steel, and have six separate storage-rooms of which four have big doors. When planning and designing the compartments we aim for maximum loading capacity, chassis adaption as well as current laws and regulations are all taken into consideration. The doors are type jalousie, made in aluminium with lock on all six doors.

WINCH

BB 9037
Standard winch is Sepson H300G, specification as below:
  • Hydraulic spur gear winch
  • An air operated dog clutch for free spooling of the wire
  • Automatic instantaneous hydraulic breaking holds the wire at any point, also under full load
  • The winch has automatic speed control and gears down when pulling exceeds approx. 3 ton
  • Operation from rear control valve

Specification

Full hydraulic operation with bare drum rated capacity of 30 ton (DIN 15020).
Wire speed step one, inner layer 3,0 m/min
Wire speed step one, outer layer 5,0 m/min
Wire speed step two, inner layer 8,0 m/min
Wire speed step two, outer layer 13,0 m/min
Wire length 40 m
Wire diameter 26 mm
BB 9068
Standard winch is Sepson H100PF, specification as below:
  • Hydraulic planetary winch
  • Pneumatic free spool of the cable drum
  • Automatic instantaneous hydraulic breaking holds the wire at any point, also under full load

Specification

Full hydraulic operation with bare drum rated capacity of 10 ton (DIN 15020).
Wire speed, inner layer 6,0 m/min
Wire speed, outer layer 9,0 m/min
Wire length 40 m
Wire diameter 16 mm
Linantrummans diameter 22 mm

ELECTRICAL SYSTEM

BB 9016
  • sub frame
  • Two revolving lights at rear of the recovery unit
  • Two working lights at rear of the recovery unit
  • Two working lights at each side of the compartments
  • Start cable set 24 V, 7 m incl 6 m extension cable)
  • Start booster, 12 V with charger
  • One compartment light LED 500 lumen

HYDRAULIC SYSTEM

BB 9013
HHydraulic tank ca. 200 l
Hydraulic pipes DIN 2391/C
Suction and return hose with wrapped up steel spiral SAE 100/R4
Hydraulic hoses with pressed couplings SAE 100/R2T
High pressure filter 10 µm
Return oil filter 10 µm
Mineral oil  
BB 9021
PTO driven hydraulic piston pump with emergency stop 300 bar
BB 9025
Directional control valve Danfoss PVG 32
The unit consists of five sections connected in parallel with built-in relief, chock and anti-cavitation valve
BB 9022
Manöverenhet Danfoss PVG 32
The unit consists of one section with built in chock and anti-cavitation valve
BB 9019
The directional control valve is fitted in the rear compartment on the right hand side.

STANDARD EQUIPMENT

BB 9033
The following tools and accessories are included in the standard equipment.Above tools are chromated.Above tools are chromated.Above tools are chromated.Above tools are chromated.
One pair of fork holders, low 3.04.0128
One pair of fork holders, high 3.04.0126
• Six pairs of forks 3.04.0006
3.04.0007
3.04.0009
4.04.0604
4.04.0172
3.04.0307
Tow jaw attachment with three pins and 50/60 tow ball BB 2216
Tow bar, DIN 40/40 3.04.1144B
Side stabilizer 4.04.0200
Spare wheel carrier with lift 3.04.0218
Above tools are chromated.
Tie down ratchet for bus-grid, one pair M275030
One pair of tie down ratchet with hook for bus grid 2HIA65100
One pair of tie down ratchet with hook for passenger car M144302
Tow chains with shortening-hooks I-GG-GG-7/8-8-18
One strap reeling device M165121
Ett par spännband till personbil M144302
Spade, iron-bar and broomt  
Chain sling 1-part ZE-13-8-2.0
Chain sling 2-part ZZE-13-8-2.0
Shackle 9.4 ton-M=39 2pcs 007828390
Shackle 7.5 ton-M=23 2pcs 007828330
Snatch block 40 ton 28.17.108
Snatch block 60 ton 28.27.100
Busgrid half, designed for trucks BB2216

MISCELLANEOUS

BB 9035
BB 9200
  • Duomatic, if chassis is prepared for it
  • CE documentation
  • Air hose 20m, 3/8” with a shut off valve

PAINTING

BB 9061
  • Painting on outside compartments. (same color as the cabin)
  • Painting inside compartments in RAL7040 grey

 

25